Progecad 2018 tutorial how to#
Progecad 2018 tutorial free#

Wood CAD Hatch patterns of different shapes and textures used for engineering and construction drawing design. Save the changes to this drawing and Close the file.Draw a rectangle and divide it into quadrants.Use Fillet to complete the drawing (radius is still 1.5).(Tip: press at the first prompt to use all objects as cutting edges then pick the segments that you want to delete) Use Trim to modify the CIRCLEs as shown below.Use a similar technique to Fillet the other three corners.Then pick the LINEs near P1 and P2 to add a Fillet ARC in that corner. Right-click in the drawing area to invoke a shortcut and select Repeat Fillet.you just set the Radius to 1.5 for the next Fillet command.The last time this drawing was saved the FILLETRAD system variable was 0 (TRIMMODE was set by T08.scr on page 5) Select Radius and then type 1.5 as the new fillet radius. Pick Modify + Fillet and right-click in the drawing area to invoke a shortcut.Open the T108_4.dwg drawing in your personal folder.Close the drawing from the previous exercise if it is open.Select first object or : (right-click to select Polyline option) if an ARC segment separates two LINE segments AutoCAD removes the ARC segment & replaces it with the fillet ARC.Д¬urrent settings: Mode = TRIM, Radius = 0.5000.a fillet ARC segment is inserted at each vertex of a 2D polyline where two LINE segments meet.You can also apply Fillet to an entire LWPOLYLINE.

Progecad 2018 tutorial how to#

See also How to use OFFSET command and Makes Parallel Objects Select second object: (pick LINE near P2) Select first object or : (pick LINE near P1) The required radius is calculated & used automatically withoutД¬hanging the radius saved in the FILLETRAD system variable.ДЄutoCAD changes the second LINE that you select if the LINEs must be adjusted in length.Д¬urrent settings: Mode = TRIM, Radius = 0.0000

It can be important where you select objects to Fillet.ДЄutoCAD uses the selection point to determine what part of the LINE or ARC to keep when these objects are trimmed.

for example, the four inside corners of the gasket shown below would require four separate Fillet commands.

to repeatedly use Fillet you can right-click in the drawing area & select Repeat Fillet to invoke this command from a shortcut.

you are prompted to select two LINEs or ARCs to Fillet.

You can only create one ARC in a single Fillet command.

This setting is saved in the TRIMMODE system variable which is stored in your system registry (initial value is Mode = Trim ) Use the Trim option of Fillet and select No Trim if you do not want to change the lengths of these selected LINEs & ARCs. If Mode = Trim the lengths of LINEs & ARCs you select for Fillet are adjusted to terminate at the endpoints of the new ARC. The current Trim Mode setting is also reported as one of the current settings on the command line when you invoke Fillet. You must invoke Fillet again to use the new radius.

п‚ the current radius is stored in the FILLETRAD system variable of the current drawing & is used automatically for the next Fillet.

The Fillet command is terminated when you use the Radius option to set the new current radius. вЂ“ right-click in the drawing area to invoke a shortcut and pick Radius to change the current radius.Д¬urrent settings: Mode = TRIM, Radius = 0.7500 When you invoke Fillet the current radius is reported on the command line but you can use the Radius option to change it.

for example, you can clean up corners in architectural plans if you Offset one side of a wall to create the other side.

You can use a Fillet Radius of zero to force LINEs & ARCs to terminate in a corner at the point of intersection.

for example, it would be a challenge to create the shape shown below if you used ONLY the Arc command.ДЇillet is also practical to use when LINEs meet or cross (or would meet if they were extended) in a corner to create a round corner.

in many cases an ARC is easier to construct using Fillet than it is using the Arc command.

Use Fillet to create a new ARC object that blends between two existing LINEs or ARCs.

Progecad 2018 tutorial free#

Here is a free courseВ How to use FILLET command in AutoCAD